+44 (0)1638 660 629

ET-5MS-OEM Industrial Ethernet Switch

Board-Level Industrial Connectivity

Industrial_Switch_board_levelThe ET-5MS-OEM is a 6 port managed industrial Ethernet switch designed for OEM-embedded applications. This powerful board-level solution enables organizations to save time and money by private labeling state-of-the-art industrial switches.

 

 

 

Overview

Industrial Switch Product Highlights

  • Board-level solution for embedded applications
  • 6 ports – including one MII – for flexible interfacing
  • 4 10/100 PHYs and magnetics on board
  • Extra output lines to drive external LEDs
    Low power consumption of less than 2 watts
  • Compact 3.5 x 2.5” (8.9 x 6.4 cm) design

Just add your own packaging, power supply and connectors and you have your own custom industrial Ethernet switch.

Features

Real-Time Ethernet Performance

  • Fast wire-speed switching
  • Intelligent message routing – no collisions
  • Real-time Ring® and Rapid Spanning Tree (RSTP) for fast redundant ring or mesh connections
  • SNMPv1 and v2 network management
  • SNMPv3 authentication and encryption for security
  • SNMP notifications (traps) for report on event
  • Priority Queuing (QoS/CoS) for real-time operation
  • IGMP for multicast filtering (snooping and querying)
  • VLAN for convenient traffic segregation
  • Broadcast and multicast storm protection
  • RMON and port mirroring for advanced diagnostics
  • Security with HTTPS, SSL, SSH, SNMPv3 and more
  • Easy to use interfaces: web, CLI or Telnet
  • Free firmware upgrades forever

Trouble-Free Operation

  • Ultra-reliable 1,000,000+ hours MTBF
  • UL/CSA (CUL), CE and hazardous locations (Zone 2) rated
  • -40 to 75°C operating range
  • Self-test/alarm output signal

Specs

Ethernet Performance

  • Fully managed with 6 Ethernet ports
  • Store and forward, wire-speed switching
  • Automatic address learning, aging and migration
  • Full duplex operation with flow control (no collisions)
  • All IEEE 802.3 Ethernet protocols supported
  • 2048 MAC addresses supported
  • Memory bandwidth: 3.2 Gbps
  • Typical latency (varies on load)
    • @ 100 Mbps: 5 µs + frame time
    • @ 10 Mbps: 16 µs + frame time
  • Ethernet isolation: 1500 VRMS 1 minute
Ethernet Ports
  • 6 fast (10/100) Ethernet ports total
    • 4 with on-board PHYs and magnetics; these are available through board-to-board or ribbon connector
    • 1 with on board PHY (by requires external magnetics); available through board-to-board connector
    • 1 is an MII port for interface to an external CPU or PHY or fiber optic transceiver; available through board-to-board connector
  • Ports support plug and play operation
    • Auto-negotiation for 10 or 100 Mbps
    • Auto- MDI/MDIX-crossover for any either cable type
    • Auto-polarity corrects for crossed +/- signals
Ethernet Compliance
  • IEEE 802.3 (10Mbps Ethernet supports legacy devices)
  • IEEE 802.3u (Fast Ethernet 100Mbps for newer devices)
  • IEEE 802.3x (Full-Duplex with Flow Control)
  • IEEE 802.1D/w, 802.1p, 802.1Q and much more
Power Input
  • Power input voltage: 3.3 VDC (regulated)
  • Input power (typical – all ports active at 100 Mbps): <1.65 W (<500 mA @ 3.3 VDC)
Environmental
  • Operating temperature: -40 to 75°C (cold start-up at -40) with proper heat-sinking
  • Storage temperature: -40 to 85°C
  • Humidity: (non-condensing) 5 to 95% RH
  • Vibration and shock: IEC68-2-6, -2-27 and -2-32 with proper mounting
Standards & Compliance
  • Electrical safety: UL508/CSA C22/14, EN61010-1, CE
  • EMC: FCC part 15, ICES-003, EN55022, EN610006-2/4, CE
  • Hazardous Locations: UL1604/CSA C22.2/213 (Class I, Division 2); EN60079-15 (Zone 2, Category 3), CE (ATEX)
  • RoHS and WEEE compliant
  • ISO9001:2008 certified company

Order Guide

Part NumberDescription
ET-5MS-OEM-2-1Industrial OEM switch with only Molex connectors*
(for board-to-board and ribbon interfaces)
ET-5MS-OEM-2-1B**Industrial OEM switch with Samtec connectors
(2 for board-to-board connections) plus Molex ribbon interface*
A test fixture is also available. Contact Sixnet for details.

* Reference mechanical diagram for location of connectors.
** Recommended for all new designs

For more information

    Contact Network specialists Ring UK today for professional advice about which system you should go for. We will assess your requirements and research and explain all the options available to you to help you or your client choose a perfect product that meets your needs.

Contact us via our Network Enquiry Form

 

Please Share Our Content
Share on LinkedIn
Linkedin
Tweet about this on Twitter
Twitter
Share on Facebook
Facebook
Print this page
Print
Email this to someone
email